SNx4HC595

SNx4HC595 is a library for SN54HC595 and SN74HC595.
It chip has 8 output IO and these are controlled from 3(minimum) wire.
So this is called "io extender".
Additionally, this chip can be connected like chain. You can extend io by chaining 8,16,24,,,.

Reference
http://www.ti.com/lit/ds/symlink/sn74hc595.pdf

obniz.wired('SNx4HC595', {ser, rclk, srclk [, gnd, vcc, oe, srclr, io_num]});

Specify which obniz Board io is connected to each pin.

name type required default description
ser number(obniz Board io) yes   connected obniz Board io
rclk number(obniz Board io) yes   connected obniz Board io
srclk number(obniz Board io) yes   connected obniz Board io
vcc number(obniz Board io) no   If you specify either vcc/gnd, wire() will wait a moment after power up.
gnd number(obniz Board io) no   If you specify either vcc/gnd, wire() will wait a moment after power up.
oe number(obniz Board io) no   oe controls output tri-state. off for normal operation.This is optional. You don't need to specify oe when oe is connected directly to GND.You can use setEnable() function when specify oe. By default, oe is set to enabled state.
srclr number(obniz Board io) no   srclr clear shift resistor values. You don't need to specify srclr when srclr is connected directly to 5v.
io_num number no 8 io_num is number of io. You can set under 8. If you specify over 8 like 16, then obniz Board will treat chained chip.
enabled boolean no true If oe was specified, you can set initial enable/disable with this parameter.

Please note that the arrangement depends on the product

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4});
ioext.output(3, true)
// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4, io_num:16});
ioext.output(0, true)  // first chip's io
ioext.output(15, true) // next chip's io

ioNum(num)

This is equal to io_num on wired().
After calling this. all number of output will be changed to false.

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4});
ioext.ioNum(16);
ioext.output(15, true)

output(io, value)

output io with value. The others will not be affected. Only specified io.

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4});
ioext.output(3, true)
ioext.output(4, true) // io4 will be changed to true "after" io3 changed to true.
ioext.output(5, true)

onece(function)

This chip can change it's output at same timing.
This function let you use it.
Set values within this function.

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4});
ioext.onece(function(){ // io 4 and 5 will be changed to false state at same timing.
  ioext.output(4, false)
  ioext.output(5, false)
})

getIO(io)

Retriving io object. io object works like a obniz Board io. You can call output().
Additionaly, you can use this io for io in LED and 7SegmentLED.

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4});

var io1 = ioext.getIO(1);
io1.output(true);

var io2 = ioext.getIO(2);
var led = obniz.wired("LED", {anode: io2});
led.blink();

var io3 = ioext.getIO(3);
var io4 = ioext.getIO(4);
var seg = obniz.wired("7SegmentLED", {a:io3, b: io4, c: 5, d:6, e:7, f:8, g:9, common:10});
seg.print(0);

setEnable(enabled)

This function available only when oe was specified.
Changing Normal-operation/Hi-Z on all of it's chip output.

// Javascript Example
var ioext = obniz.wired('SNx4HC595', {gnd:0, vcc:1, ser:2, rclk:3, srclk:4, oe:5, enabled: false});
ioext.output(0, true); // no affect
ioext.setEnable(true); // 0 is true


Found at :




You will Get in Few Days

Circuit for Starter “obniz Board” is available on Amazon and other online stores.
You can get it at below

Our products and resellers

Forum

Visit our developer’s forum to discuss and discover technologies.

Forum

Contact

Feel free to contact out support and technical team.

Contact us